KAOSS PAD
DYNAMIC EFFECT/CONTROLLER
EasyStart
KP3 Main Features
•
•
Third Generation KAOSS EFFECTS! 128 Effect Programs – Both favorites and new! Reverb, Delay, Flanger,
Modulation, BPM Synced effects, grain shifter, decimator, a vintage analog style filter with a tone-bending drive
circuit, expanded EQs, drum grooves and RADIAS-inspired vocoder and synthesizer sounds.
Sampling/Resampling - 16bit 48kHz sampling up to 16 beats long on each SAMPLE BANK button. Sample
slicing, auto looping and more!
•
•
•
•
•
•
•
AUTO BPM Detection, MIDI Clock and Tap tempo keep turntables and MIDI devices in time with KP3.
FX Release feature. Blend from effected to dry signals. Smooth or rough-edge transitions can be set to taste.
Microphone input for vocal, pitch shift and vocoder effects.
SD Card slot - Save and load your samples and settings with convenient, affordable SD cards.
New Touch Pad LEDs provides a variety of visual cues and can even scroll custom messages!
Built-in USB port provides direct connection to your computer.
FREE bundled software Editor included! Build libraries of samples, and edit them using your computer. The
KP3 Editor also allows WAV and AIFF files to be loaded into the KP3, and includes pitch correction for samples
not created at 48 kHz.
•
MIDI controller functionality. Up to eight different CC#s on eight MIDI channels can be transmitted
simultaneously form the Touch Pad alone! Sample Bank buttons send and receive note messages.
EasyStart CONTENTS
A Quick Overview of Buttons, Knobs and Switches
Connecting the KP3
2
3
Selecting Programs and Working with PROGRAM MEMORY Buttons
Four Programs to Try
3
3
Sampling a Loop/ Loop Slice and Loop Adjust / Resampling a One Shot Sample
The PAD MOTION function
4
5
The FX RELEASE function
5
Formatting / Saving and Loading using SD memory cards / USB Mode
The KP3 Editor/Librarian Software
5-6
6
KP3 EasyStart
Connecting the KP3
1. Connect the LINE OUT L, R jacks to the line input of your DJ mixer, line mixer, or connect to the FX Return
of your DJ mixer if so desired.
2. Set the CONNECTION switch to either DIRECT or SEND. Only set the CONNECTION switch to SEND if you
are using the KP3 in an FX Send/Return configuration.
3. Connect your line input source to the LINE IN L, R jacks or a microphone to the 1⁄4” MIC input on the front.
Set the INPUT SELECT switch to the corresponding input.
4. Adjust the input level using the INPUT VOLUME knob so that the PEAK LED does not turn RED. If a
microphone is being used, first adjust the MIC TRIM knob so the sound is not distorted.
Selecting Programs and Working with PROGRAM MEMORY Buttons
There are 128 effect programs in the KP3 and these include some great new effects! Eight
favorite programs can be saved to the eight PROGRAM MEMORY buttons.
1. If the display is showing the current BPM, PRESS the PROGRAM/BPM knob to switch to the program display.
2. HOLD the SHIFT button and rotate the PROGRAM/BPM knob to select by category. The display will show
the category and program number (Example: Flt.1 or Voc.1). When a program is selected, the TOUCH PAD
will display and scroll the program name!
3. Select program “Syn.1” and rub the TOUCH PAD. Nice synth sound! You can tell that this program
synchronizes to BPM by the blinking BPM indicator to the right of the display.
4. Rotate the PROGRAM/BPM knob clockwise to advance to the next program. The PROGRAM/BPM knob is
continuous so when the last program is reached it will wrap around to the beginning of the list.
5. Eight favorites can be stored on the PROGRAM MEMORY button. Simply press one of these eight buttons to
recall a stored program.
6. To store a program to a PROGRAM MEMORY button, press the WRITE button. The PROGRAM MEMORY
and the WRITE buttons will blink. Press the PROGRAM MEMORY button to which you want to save the
program. Press WRITE to exit without saving.
FOUR PROGRAMS TO TRY
drM.2 BeatBox
Beat Box
X AXIS changes patterns
Y AXIS controls delay depth
X AXIS Synth pitch
SYn.1 SawBass
Unison Saw Bass
Voc.1 Vocoder
Vocder
Y AXIS HPF Cutoff & Resonance
X AXIS Pitch
Y AXIS Vocoder tone
SMP.2 SmplRoll
Sample Roll
X AXIS Sample Length (1/1, 1/2, 1/4….1/128)
Y AXIS HPF Cutoff & Resonance
Note: See the EFFECT PROGRAM LIST included with the KP3 for a detailed program list.
3
KP3 EasyStart
Sampling and Resampling
The KP3 can record both looped phrases and one shot samples from an external source,
resample external audio sources through effects, or capture the entire output of the KP3 as
a new sample. Loop samples can be sliced into eight equal parts. These parts can be turned
on and off to create new rhythmic figures and loops. Four SAMPLE BANK buttons allow you
to create, play and save samples up to 16 beats (4 bars) on the fly. All samples are
recorded using high-resolution 24-bit converters, and are stored in16-bit/48 kHz format.
SAMPLING A LOOP
1. Adjust the BPM by tapping it in using the TAP/RANGE button, or by using the PROGRAM/BPM knob to set
the desired tempo.
2. Press the SAMPLING button. The SAMPLE BANK buttons will blink red and the display will indicate “[16]”
This is the default value of 16 beats. (To exit without sampling, press the SHIFT button)
3. Rotate the PROGRAM/BPM knob to specify the length of sampling in beats. The display will switch between
[16], [8], [4], [2] or [1] accordingly.
4. When you are ready to record, press one of the SAMPLE BANK buttons. The recording starts as soon as you
press the SAMPLE BANK button. The PROGRAM MEMORY buttons will consecutively blink to indicate the
beat you’re recording. The sample will automatically loop when the recording is finished. The SAMPLE BANK
button will be lit ORANGE and the loop will automatically play and loop.
5. To stop playback, press the SAMPLE BANK button and it will turn GREEN, indicating a loop sample is
present.
LOOP SLICE and LOOP START ADJUSTMENT
6. Press and hold the SHIFT button then press the SAMPLE BANK button where the loop was just recorded. By
pressing the lit PROGRAM MEMORY buttons, slices can be turned and off. Try turning a few on and off to
hear other rhythmic variations of the loop. (Note that the sliced parts that are off are skipped, making the
overall sample shorter)
7. Turn all eight PROGRAM MEMORY buttons ON so that all slices are playing. Rotate the PROGRAM/BPM
knob to adjust the Loop Start point in steps of 1/32nd of a beat, over a range of +/-1.
8. Press the SHIFT button to exit.
RESAMPLING A ONE SHOT SAMPLE
1. For this example, select one of the synth Programs (“Syn.1” – “Sy.10”).
2. Hold down the SHIFT button and press the SAMPLING [RESAPMLING] button. The SAMPLE BANK
buttons will blink ORANGE.
3. Rotate the PROGRAM/BPM knob and set the number of beats to “[16]” in the display.
4. Press one of the SAMPLE BANK buttons and rub the TOUCH PAD to trigger the synth sound to be sampled.
5. Stop the sample recording before the end beat is reached by pressing the SAMPLE BANK button.
6. The SAMPLE BANK button will be lit RED, indicating there is a one shot sample present.
4
KP3 EasyStart
The PAD MOTION function
Pad Motion allows you to record and playback a motion (several seconds long) of your finger
on the TOUCH PAD. This allows you to reproduce complicated moves. The TOUCH PAD LEDs
will provide a visual of the movement.
1. To record a pad motion, press and hold the PAD MOTION button. Recording will begin as soon as you touch
the TOUCH PAD.
2. To play back the recorded motion, press the PAD MOTION button: it will light and play the motion
repeatedly until you press it again so it is dark (unlit).
3. The Pad Motion can be REVERSED by holding the SHIFT button, then pressing the PAD MOTION
[REVERSE] button. You can alternate direction by repeating this operation.
Note: Pad Motion recordings can be saved as part of a Program!
The FX RELEASE function
Making the transition from a hard-edged effect back to the original unaffected signal can
often times be very abrupt. With FX RELEASE, the moment you take your hand off the touch
pad, a gradually diminishing delay effect in sync with the current BPM is applied. This allows
you to make a smooth and musical transition. A “sharp” transition can be achieved by
setting the FX RELEASE fader all the way down.
1. Press and hold the SHIFT button while moving the FX RELEASE fader down to decrease the amount of
“transition smoothness”.
Saving and Loading using SD Memory Cards
SD memory cards up to 2GB can be used to load and save data. WAV or AIFF files can also
be loaded into the KP3 from an SD card. Files on a KP3’s SD card can be managed by a
computer, when connected to the KP3s USB port.
Note:
THE KP3 MUST BE TURNED OFF BEFORE INSERTING OR REMOVING AN SD CARD!
FORMATTING AND SAVING DATA TO A CARD
1.
2.
With the KP3 powered OFF, insert an SD memory card. Power ON the KP3.
Press and hold SHIFT while pressing PROGRAM MEMORY 1 [CARD], then rotate the PROGRAM/BPM
knob clockwise to select “ForM” (format) in the display. Press the PROGRAM/BPM knob to confirm and
format the SD card. THIS WILL ERASE ALL DATA FROM THE CARD!
3.
4.
To save the entire contents of the KP3, including favorites, settings and samples, Press and hold SHIFT while
pressing PROGRAM MEMORY 3 [SAVE].
Rotate the PROGRAM/BPM knob to select “ALL” in the display, and then press the PROGRAM/BPM to
confirm. Rotate the PROGRAM/BPM to select [0] in the display. Press the PROGRAM/BPM 2x to confirm.
Note: When an SD card is inserted prior to powering up the KP3, it will automatically load the samples
stored as an “All” file in memory location [0].
5
KP3 EasyStart
USB MODE
1. Connect a USB cable from the KP3 to your computer’s USB connection.
2. Press and hold the SHIFT button, then press PROGRAM MEMORY button 7 (USB).
3. The SD card will mount on your computer and files can be transferred to and from the card.
4. When finished, drag the mounted card into the trash (MAC) or eject it from your computer (PC), then Press the
SHIFT button on the KP3 to exit USB mode.
Note:
See pages 18, 22-23 of the KP3 OWNER’S MANUAL for information on SD cards and sharing data
with a computer via USB.
KP3 Editor/Librarian Software
Included with the KP3 is a CD-ROM containing the KP3 Editor/Librarian. This is invaluable
software that adds the computer as part of your arsenal. With this editor/librarian tool, you
can manage your samples and custom programs, import and export samples as WAV and
AIFF, assign a custom scrolling message to the Touch Pad, and more!
The KORG USB MIDI Driver, Demo samples and the KP3 Editor Owner’s Manual can also be
found on the included CD-ROM. Enjoy your KP3!
Note: See pages 24-26 of the KP3 OWNER’S MANUAL and the KP3 Editor PDF manual for information on
installing and using the KP3 Editor/Librarian software as well as detailed system requirements.
information for your KP3 and other KORG products!
6
|