GIGA X7c Professional Instructions for Use
Original instructions for use
E
K
Before using the machine read the instructions for use.
Instructions for use has been awarded the seal of approval by the inde-
pendent German Technical Inspection Agency, TÜV SÜD, due to its weasy-
to-understand style, its thoroughness and coverage of safety aspects.
JURA Type 689
Table of contents
5
Maintenance
40
Rinsing the coffee system .........................................................................................................................40
Rinsing the milk system..............................................................................................................................41
Cleaning the milk system...........................................................................................................................41
Dismantling and rinsing the dual spout.................................................................................................42
Changing the filter......................................................................................................................................45
Cleaning the machine ................................................................................................................................45
Descaling the machine ..............................................................................................................................46
Cleaning the bean container.....................................................................................................................49
6
7
8
Display messages
Troubleshooting
50
52
53
Transport and environmentally friendly disposal
Transport / Emptying the system.............................................................................................................53
Disposal.........................................................................................................................................................53
9
Technical data
54
55
60
10 Index
11 JURA contact details / Legal information
Symbol description
Warnings
Always take note of any information marked with the words CAUTION or
WARNING and a warning sign. The signal word WARNING draws your attention
J WARNING
J CAUTION
to potential serious injury, and the signal word CAUTION to potential minor
injury.
CAUTION
CAUTION draws your attention to potential damage to the machine.
Symbols used
Prompt to take action. This symbol means that you are being prompted to
perform some action.
T
Information and tips to make it even easier to use your GIGA.
E
‘Espresso’
Display
3
Control elements
Control elements
1
9
2
3
10
11
4
12
13
14
15
5
6
7
8
1
Bean container with aroma
9
Filler funnel for ground coffee
preservation cover
Bean container status indicator
Water tank cover
10 Ventilation slats (Venti Ports)
11 Storage compartment cover
12 Measuring spoon for ground coffee
13 Height- and width-adjustable dual spout
14 Splash guard
2
3
4
5
Water tank
Power switch and plug-in mains
cable (back of the machine)
Coffee grounds container
Drip tray
15 Height-adjustable hot-water spout
6
7
8
Cup grille
4
Control elements
ꢀ
ꢄ
ꢃ
ꢁ
ꢂ
Top of the machine
Front
1
Q
g
O
On/Off button
Rotary Switch
4
5
Display
Multi-function buttons (button function
2
3
P button (programming)
depends on what is shown in the display)
ꢀ
ꢄ
ꢃ
ꢁ
Back of the machine
1
Service cover (open by pressing with
your finger)
3
4
Sliding catch
Service socket (underneath cover)
2
Locking device
5
Important information
Important information
Proper use
This machine is intended for use by specialist or
trained staff in businesses, light industry and agri-
cultural facilities or for commercial use by non-pro-
fessionals. It should only be used for coffee prepa-
ration and to heat milk and water. Use for any other
purpose will be deemed improper. JURA Elektro-
apparate AG cannot accept any responsibility for
the consequences of improper use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty ser-
vice is not applicable for damage or defects caused
by non-compliance with the instructions for use.
Keep these instructions for use close to the machine
and pass them on to the next user.
The GIGA may only be operated by instructed
persons. Non-professionals must be supervised
during use.
For your safety
Please carefully read and observe the important
safety information set out below.
To avoid danger of potentially fatal electric shock:
Never use a machine which is damaged or has
a defective mains cable.
U
In the event of signs of damage, for example if
U
J
there is a smell of burning, unplug the machine
immediately from the mains supply and con-
tact JURA service.
If the mains cable of this machine is damaged,
it must be repaired either directly by JURA or
by an authorised JURA service centre.
U
6
Important information
Make sure that the GIGA and the mains cable
are not located close to hot surfaces.
U
U
U
Be careful to ensure that the mains cable is not
trapped and does not rub against sharp edges.
Never open and repair the machine yourself.
Do not modify the machine in any way that is
not described in these instructions for use. The
machine contains live parts. If opened, there is
a danger of potentially fatal injury. Repairs
may only be carried out by authorised JURA
service centres, using original spare parts and
accessories.
To completely and safely disconnect the
machine from the power supply, first switch
off the GIGA using the On/Off button and then
at the power switch. Only then should you
remove the mains plug from the power socket.
U
There is a risk of scalds or burns on the spouts.
Place the machine out of the reach of children.
Do not touch any hot parts. Use the handles
provided.
U
U
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
Never allow the mains cable to loosely hang
down. The mains cable could pose a tripping
hazard or become damaged.
U
Protect the GIGA from environmental influ-
ences such as rain, frost and direct sunlight.
U
Do not immerse the GIGA, mains cable or con-
nections in water.
U
Do not put the GIGA or any individual parts in
the dishwasher.
U
7
Important information
Switch your GIGA off at the power switch
before any cleaning operation. Always wipe
the GIGA with a damp cloth rather than a wet
one, and protect it from prolonged exposure
to water splash.
U
The GIGA is not suitable for installation on a
surface where a jet of water can be used.
The machine must not be cleaned with a jet of
water.
Only connect the machine to the mains volt-
age in accordance with the information on the
rating plate. The rating plate is located on the
underside of your GIGA. Further technical data
is provided in these instructions for use (see
Chapter 9 ‘Technical data’).
U
U
U
Please only use original JURA maintenance
products. Use of products that are not explic-
itly recommended by JURA could damage the
GIGA.
Do not use any coffee beans treated with addi-
tives or caramelised coffee beans.
U
U
Only fill the water tank with fresh, cold water.
Switch the machine off at the power switch if
you are going to be absent for a longer period
of time.
U
U
Children may not clean or service the machine
unless supervised by a responsible person.
Do not allow children to play with the machine.
Keep children under the age of 8 away from
the machine, or supervise them constantly.
U
U
U
8
Important information
Children aged 8 and over may only operate
the machine without supervision if they have
been instructed in how to use it safely. Chil-
dren must be able to recognise and under-
stand the potential dangers arising from incor-
rect use.
U
People, including children, who
do not have the physical, sensory or mental
capabilities to use the machine safely or
U
are inexperienced or lack knowledge in how to
use the machine safely
U
must be supervised by a responsible person when
using it, or must be instructed in how to use it cor-
rectly.
Safety when handling the CLARIS filter cartridge:
Filter cartridges should be kept out of the
reach of children.
U
Store filter cartridges in a dry place in the
sealed packaging.
U
Protect cartridges from heat and direct sun-
light.
U
Do not use damaged filter cartridges.
Do not open filter cartridges.
U
U
9
1
Preparing and using for the first time
1
Preparing and using for the first time
Visit us on the Internet.
JURA on the Internet
up-to-date information on your GIGA and on every aspect of coffee.
A few preparations are necessary before the JURA service technician
can set up your GIGA in your home. The following preparations must
be carried out by a professionally qualified person:
Requirements for
first-time use
The mains connection for the GIGA must be protected by a
U
residual current device (RCD).
There must be a power switch to disconnect the power supply
U
to the GIGA.
The permanent water connection must have a shut-off valve
U
with a non-return valve (type EA) and filter.
The permanent water connection must comply with the spec-
U
ified technical data,(see Chapter 9 ‘Technical data’).
The drain hose must be connected to a siphon.
U
E
These preparations must be carried out by a qualified person.
The preparations must be carried out before the JURA service
technician sets up your GIGA in your home.
E
When setting up your GIGA, please note the following:
Setting up the machine
Filling the bean container
Place the GIGA on a horizontal surface that is not sensitive to
U
water.
Choose a spot for your GIGA which protects the machine
U
against overheating. Ensure that the ventilation slats are not
covered.
The bean containers have an aroma preservation cover. This will
ensure that your coffee beans retain their aroma for longer.
CAUTION Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinders.
T
Only use untreated coffee beans to fill the bean containers.
T Remove the aroma preservation cover.
10
1
Preparing and using for the first time
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
E
Before the machine is used for the first time, the permanent
water connection must be installed by a JURA service techni-
cian.
First-time use
During first-time use, you can choose between ‘Quick installation’
and ‘Expert mode’.
‘Quick installation’: After setting the time and date, your GIGA
U
is ready for use.
‘Expert mode’: Here, you can also choose whether you oper-
U
ate your GIGA with or without the CLARIS filter cartridge.
‘Use filter’ / ‘Active’: Here, you can set the capacity of the
U
external filter cartridge you are using.
‘Use filter’ / ‘Inactive’: Here, you can set the water hardness
U
of the water used. This setting influences when your GIGA
prompts you to perform descaling. If you do not know the
hardness of your water, you can find this out first (see Chap-
ter 1 ‘Preparing and using for the first time – Determining
the water hardness’).
J
WARNING If the machine is operated with a defective mains cable, there is a
danger of potentially fatal electric shock.
T
Never use a machine which is damaged or has a defective
mains cable.
Precondition: The bean containers have been filled.
T Connect the mains cable to the machine.
T Insert the mains plug into a power socket.
3
T Switch on the GIGA using the power switch on the back of
the machine.
Q
T Press the On/Off button to switch the GIGA on.
‘Welcome to JURA’ appears on the display. The display then
shows the languages you can choose from.
11
1
Preparing and using for the first time
E
E
To display more languages, press the ‘Next’ button (bottom
right).
T Press the button that corresponds to the language you want,
e.g. ‘English’.
‘Saved’ appears briefly on the display to confirm the setting.
‘First-time use’
Now choose between ‘Quick installation’ and ‘Expert mode’.
Quick installation
T Press the ‘Quick installation’ button.
‘Time’
T Press the ‘+’ or ‘–’ button to set the hours.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the minutes.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Date’
T Press the ‘+’ or ‘–’ button to set the year.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the month.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the day.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Press the Rotary Switch.’, the Rotary Switch lights up.
T Place a receptacle under the dual spout.
T Press the Rotary Switch.
k
k
‘System is filling.’, the system fills up with water. The opera-
tion stops automatically. ‘Welcome to JURA’, ‘Machine is
heating.’, ‘Press the Rotary Switch.’ appears on the display.
T Press the Rotary Switch.
‘Machine is rinsing.’, the machine rinses. The operation
stops automatically. ‘Please select product:’ appears on the
display. Your GIGA is ready for use.
12
1
Preparing and using for the first time
Expert mode
T Press the ‘Expert mode’ button.
‘Time’
T Press the ‘+’ or ‘–’ button to set the hours.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the minutes.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Date’
T Press the ‘+’ or ‘–’ button to set the year.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the month.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the day.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Use filter’
E
Now choose whether you operate your GIGA with or without
the CLARIS filter cartridge.
Activating the filter
T Press the ‘Active’ button.
T Press the ‘Save’ button.
‘Filter’ / ‘Filter capacity in litres:’
T Press the ‘+’ or ‘–’ button to set the first digit of the filter
capacity.
E
You can also change the value by turning the Rotary
Switch f.
T Press the ‘Save’ button or the Rotary Switch k to confirm
the setting for the first digit.
T Now select the other digits for filter capacity.
‘Saved’ appears briefly once the last digit has been con-
firmed.
‘Machine is heating.’, ‘Press the Rotary Switch.’.
T Press the Rotary Switch.
k
‘System is filling.’, the system fills up with water.The opera-
tion stops automatically.
13
1
Preparing and using for the first time
T Place a receptacle under the dual spout.
T Press the Rotary Switch.
k
‘Machine is rinsing.’, the machine rinses. The operation
stops automatically. ‘Please select product:’ appears on the
display. Your GIGA is ready for use.
Deactivating the filter
T Press the ‘Inactive’ button.
T Press the Rotary Switch.
‘Water hardness’
k
E
If you do not know the hardness of your water, you must find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
T Press the ‘+’ or ‘–’ button to adjust the water hardness.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine is heating.’, ‘Press the Rotary Switch.’.
T Press the Rotary Switch.
k
k
‘System is filling.’, the system fills up with water. The opera-
tion stops automatically.
T Place a receptacle under the dual spout.
T Press the Rotary Switch.
‘Machine is rinsing.’, the machine rinses. The operation
stops automatically. ‘Please select product:’ appears on the
display. Your GIGA is ready for use.
The following settings can only be made by the JURA service techni-
cian:
Settings by the JURA
service technician
Customised layout of the products on the start screen (dis-
U
play) or in the product selector
Disabling the product selector view (see Chapter 2 ‘Prepara-
U
tion – Preparation using the product selector’)
Codes: Four codes can be assigned. For each code, you can
U
define which programme items are available or disabled. Each
14
1
Preparing and using for the first time
code corresponds to different authorisations. For instance,
you can define that initiation of the maintenance programmes
is disabled using a code.
Blocking the ‘Permanently setting the amount of water for the
cup size’ function.
U
U
U
Blocking the option of preparing a double product by pressing
the button for the appropriate single product twice
Defining that a prompt to empty the drip tray does not appear
after cleaning
You can also obtain the following optional accessories for your GIGA
from your JURA service partner:
Set for automatic discharging of coffee grounds
U
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
Determining the water
hardness
T Hold the test strip briefly (for 1 second) under flowing water.
Shake off the water.
T Wait for about 1 minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
Your GIGA creates fine, creamy, feather-light milk foam with a per-
fect consistency. The most important requirement for frothing milk
is a milk temperature of 4–8 °C. We would therefore recommend
using a milk cooler (e.g. the JURA Compressor Cooler Pro, which is
available as an option).
Connecting milk
T Connect the milk pipe to the dual spout. To do this, attach
the end of the milk pipe to the connector on the right-hand
side of the dual spout.
T Connect the other end of the milk pipe to a milk cooler.
15
2
Preparation
2
Preparation
E
E
E
While a product is being prepared, you can stop preparation
at any time. To do this, press the Rotary Switch k or the
‘ꢀ’ button.
During preparation, you can change the preset amounts
(e.g. amount of milk foam or water) by turning the Rotary
Switch g.
You can follow the current status of preparation on the display.
Coffee tastes best served hot. A cold porcelain cup cools the bever-
age – and impairs the taste. We therefore recommend prewarming
the cups. The full coffee aroma can develop only in prewarmed cups.
You can purchase a JURA cup warmer from your specialised dealer.
You can make permanent settings for all products in programming
mode (see Chapter 4 ‘Permanent settings in programming mode –
Product settings’).
The GIGA provides you with two options for preparing a speciality
coffee, milk or hot water.
Coffee, latte macchiato
etc. – options for
preparation
Preparation at the touch of a button: Simply press the cor-
U
responding preparation button for the product shown on the
display (start screen) that you want.
Preparation using the product selector (Rotary Selection):
U
Only some of the products you can prepare are shown on the
start screen. As soon as you turn the Rotary Switch, more
products are displayed in a product selector.
Turn the Rotary Switch to bring the product you want into
U
focus. Start preparation by pressing the Rotary Switch or the
‘Prepare’ button.
The product selector view disappears automatically after
U
5 seconds if no preparation is started.
The two preparation options will now be described in more detail in
the following sections.
16
2
Preparation
On the display (start screen), you will see various products, which
you can prepare by simply pressing the corresponding button.
Preparation at the touch
of a button
Speciality coffees at the A speciality coffee displayed on the start screen is always prepared
touch of a button in the same way.
Example: Proceed as follows to prepare one coffee.
Precondition: ‘Please select product:’ is displayed.
T Place a cup under the dual spout.
T Press the ‘Coffee’ button.
Preparation starts. ‘Coffee’ and the fill volume are displayed.
The preset amount of water for coffee flows into the cup.
Preparation stops automatically. ‘Please select product:’
appears on the display.
Two speciality coffees at the Two speciality coffees can always be prepared in the same way: Press
touch of a button the preparation button you want twice within two seconds.
Speciality coffees with milk Your GIGA prepares latte macchiato, cappuccino and other speciality
at the touch of a button coffees with milk at the touch of a button. There is no need to move
the glass or cup.
Example: Proceed as follows to prepare one latte macchiato.
Precondition: ‘Please select product:’ is displayed, milk is connected
to the dual spout.
T Place a glass under the dual spout.
T Press the ‘Latte macchiato’ button.
‘Latte macchiato’ and the various amounts are displayed.
‘Latte macchiato’, the preset amounts of milk and milk foam
flow into the glass.
Coffee preparation starts. The preset amount of water for
espresso flows into the glass. Preparation stops automati-
cally. ‘Please select product:’ appears on the display.
To ensure that the milk system in the dual spout always works prop-
erly, you must clean it daily (see Chapter 5 ‘Maintenance – Cleaning
the milk system’).
17
2
Preparation
As soon as you turn the Rotary Switch, more products are displayed
Preparation using the
product selector
in a product selector.
E
The product selector view disappears automatically after
5 seconds if no preparation is started.
Preparation of a speciality Example: Proceed as follows to prepare a milky coffee using the
coffee using the product product selector.
selector Precondition: ‘Please select product:’ is displayed, milk is connected
to the dual spout.
T Place a cup under the dual spout.
g
g
T Turn the Rotary Switch to view the product selector.
T Turn the Rotary Switch until the ‘Caffè latte’ product is in
focus.
k
T Press the Rotary Switch to start preparation.
The milky coffee is prepared.
Preparation stops automatically. ‘Please select product:’
appears on the display.
You can choose to use a second coffee variety, for example decaf-
feinated coffee, with the filter funnel for ground coffee.
Ground coffee
E
E
Never add more than two level measuring spoons of ground
coffee.
Use ground coffee which is not ground too finely. Very fine
coffee can block up the system so that the coffee only comes
out in drips.
E
E
If you did not fill the machine with a sufficient amount of
ground coffee, ‘Not enough ground coffee.’ is displayed and
the GIGA stops the operation.
The desired speciality coffee must be prepared within approx-
imately one minute after filling with the ground coffee.
Otherwise the GIGA stops the operation and is once more
ready for use.
All speciality coffees with ground coffee are prepared following this
model.
18
2
Preparation
Example: Proceed as follows to prepare one coffee using ground
coffee.
Precondition: ‘Please select product:’ is displayed.
T Place a cup under the dual spout.
T Open the cover of the filler funnel for ground coffee.
‘Please add ground coffee.’
T Place one level measuring spoon of ground coffee into the
filler funnel.
T Close the cover of the filler funnel.
‘Please select product:’, the speciality coffees you can pre-
pare with ground coffee are displayed.
T Press the ‘Coffee’ button.
Preparation starts. ‘Coffee’ and the fill volume are displayed.
The preset amount of water for coffee flows into the cup.
Preparation stops automatically. ‘Please select product:’
appears on the display.
Now you too can be a professional barista! You can select the recipes
for 12 delicious coffee creations from the product selector using the
Rotary Switch. The GIGA will guide you through each step of the
preparation process with easy-to-follow text and pictures. Choose
from:
Barista recipes at a
glance
Marocchino
U
Pepresso
U
White Cool
U
Flavoured latte macchiato
U
Irish coffee*
U
Café mélange
U
Viennese coffee
U
Winter Magic
U
Shakerato
U
Mango Lassi
U
Red Cool*
U
Summer Fire
U
Designed to please the eye as well as the taste buds! (Recipes
marked * contain alcohol.)
19
2
Preparation
All barista recipes are prepared following this model.
Preparing barista recipes
E
The product selector view disappears automatically after
5 seconds if no preparation is started.
Example: Proceed as follows to prepare a White Cool.
Precondition: ‘Please select product:’ is displayed.
g
g
T Turn the Rotary Switch to view the product selector.
T Turn the Rotary Switch until the ‘White Cool’ product is in
focus.
k
T Press the Rotary Switch to start preparation.
T Follow the instructions on the display and confirm by press-
ing the ‘Next’ button.
E
E
E
You can stop preparation at any time by pressing the ‘ꢀ’ but-
ton.
Just before preparation starts, you are asked which grinder
and therefore which beans you want to use.
You cannot make any permanent settings for barista recipes.
During preparation, you can however change the coffee
strength and quantities by turning the Rotary Switch f.
It is easy to make permanent settings for the amounts (amount of
water, amount of milk etc.) according to the cup size for all products
except caffè latte. Adjust the amount once as shown in the following
example. Every time you prepare a drink in the future, this amount
will be dispensed.
Permanently setting
amounts for the cup size
E
Your JURA service technician can block the ‘Permanently set-
ting the amount of water for the cup size’ function.
The permanent settings for adapting the amounts to the cup size
for all products follow this model.
Example: Proceed as follows to permanently set the amount of
water for one coffee.
Precondition: ‘Please select product:’ is displayed.
20
2
Preparation
T Place a cup under the dual spout.
T Press and hold the ‘Coffee’ button.
‘Coffee’ and the fill volume are displayed.
T Hold the ‘Coffee’ button down until ‘Enough coffee? Press
button.’ appears.
T Release the ‘Coffee’ button.
Preparation starts and the coffee flows into the cup.
T Press any button as soon as there is sufficient coffee in the
cup.
Preparation stops. ‘Saved’ appears briefly on the display. The
set amount of water for one coffee is permanently stored.
‘Please select product:’ appears on the display.
E
E
You can alter this setting at any time by repeating the above
procedure.
The amount can be permanently adjusted to the cup size for
the products shown in the product selector too. To do this,
press and hold the Rotary Switch k until ‘Enough coffee?
Press button.’ appears.
E
You can also permanently set the amount for all speciality
coffees, milk and hot water in programming mode (see Chap-
ter 4 ‘Permanent settings in programming mode – Product
settings’).
You have the option of configuring the start screen such that the
grinder selection (‘beans à la carte’) is always displayed. Before each
preparation, you can select which grinder is to be used and therefore
which coffee beans are to be used.
Activating the grinder
selection
E
If the grinder selection is activated, you can no longer set the
grinder for the individual products in programming mode (in
the ‘Product settings (2/5)’ programme item).
Example: Proceed as follows to activate ‘beans à la carte’ mode.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (4/5)’ is displayed.
21
2
Preparation
T Press the ‘Café à la carte’ button.
T Press the ‘Active’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (4/5)’
O
T Press the P button to exit programming mode.
‘Please select product:’
Preparation of a speciality Example: Proceed as follows to prepare a coffee with coffee beans
coffee with grinder from the grinder on the left.
selection Precondition: ‘Please select product:’ is displayed. ‘Beans à la carte’
mode is activated.
T Place a cup under the dual spout.
T Press the ‘+’ button on the left-hand side several times until
the value is set to ‘100%’.
E
E
Press the ‘+’ button for approx. 1 second; the value is directly
set to ‘100%’.
The grinder selection remains active until the setting is
changed by you, even if the GIGA is switched off in the mean-
time.
T Press the ‘Coffee’ button.
Preparation starts. ‘Coffee’ and the fill volume are displayed.
The preset amount of water for coffee flows into the cup.
Preparation stops automatically. ‘Please select product:’
appears on the display.
22
2
Preparation
The following temperatures can be selected for preparing hot water:
‘Low’, ‘Normal’, ‘High’.
Hot water
J
CAUTION There is a danger of scalding from hot water splashes.
T
Avoid direct contact with the skin.
Precondition: ‘Please select product:’ is displayed.
T Place a cup under the hot-water spout.
T Press the ‘Hot water’ button.
‘Hot water’ and the temperature are displayed.
E
By pressing the ‘+’ or ‘–’ button (within approximately 2 sec-
onds) you can set the temperature to your individual prefer-
ence. This setting is not saved.
‘Hot water’, hot water flows into the cup. Preparation stops
automatically when the preset amount of water is reached.
‘Please select product:’ appears on the display.
23
3
Daily operation
3
Daily operation
When the GIGA is switched on, it automatically prompts you to
perform the rinse operation. Start the rinse operation by pressing
the Rotary Switch k. In programming mode you can change this
setting so that the machine starts the switch-on rinse automatically
(see Chapter 4 ‘Permanent settings in programming mode – Main-
tenance settings’).
Switching on
Precondition: Your GIGA is switched on at the power switch.
T Place a receptacle under the dual spout.
Q
T Press the On/Off button to switch the GIGA on.
‘Welcome to JURA’ appears on the display. The machine
heats up.
‘Press the Rotary Switch.’
k
T Press the Rotary Switch.
‘Machine is rinsing.’, the machine rinses. The operation
stops automatically. ‘Please select product:’ appears on the
display.
To ensure that you get many years of reliable service out of your
GIGA and to guarantee the optimum coffee quality, the machine
requires daily maintenance.
Daily maintenance
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
T Dry the metal contacts on the back of the drip tray.
T Refit the coffee grounds container and the drip tray.
T Rinse the water tank with clean water.
T Dismantle and rinse the dual spout (see Chapter 5 ‘Mainte-
nance – Dismantling and rinsing the dual spout’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfibre cloth).
E
In the interests of hygiene, we recommend changing the milk
pipe on a regular basis (approx. every 6 months). Replacement
pipes are available from specialised dealers.
24
3
Daily operation
When you switch off your GIGA, the dual spout is rinsed automati-
cally.
Switching off
Precondition: ‘Please select product:’ is displayed.
T Place a receptacle under the dual spout.
Q
T Press the On/Off button.
‘Machine is rinsing.’, ‘Milk system is being rinsed.’ (if you
have prepared a speciality coffee with milk). The system
rinses itself. The operation stops automatically. Your GIGA is
switched off.
E
When the GIGA is switched off with the On/Off button, the
machine consumes less than 0.1 W of standby energy. The
machine can be completely disconnected from the power
supply using the power switch.
25
4
Permanent settings in programming mode
4
Permanent settings in programming mode
Press the P button to enter programming mode. You can navigate
through the programme items and permanently save the required
settings simply by turning the Rotary Switch and using the multi-
function buttons. The following settings can be made:
Possible settings in
programming mode
Programme item
Sub-item
Explanation
‘Maintenance status ‘Clean’,
T Start the required maintenance programme
(1/5)’
‘Change the filter’,
here.
‘Descale’ (only if filter
is not activated),
‘Rinse the milk
system’,
‘Rinse the coffee
system’,
‘Clean the milk
system’
‘Product settings
(2/5)’
‘Expert mode’,
‘Set consistency of
grind’
T Select your settings for speciality coffees, milk
and hot water.
T Adjust the consistency of grind for both
grinders to the coffee beans used.
‘Machine settings
(3/5)’
‘Maintenance
settings’ (filter, water
hardness, switch-on
rinse, milk system
rinsing),
T Set the water hardness or activate the filter.
T Change the settings for the switch-on rinse and
milk system rinse.
T Set the time after which the GIGA should switch
off automatically.
‘Time / date’,
T Select an energy-saving mode.
‘Timer’,
T Select the unit for the amount of water.
T Reset the machine or the permanently set
values of all products to the factory settings.
‘Save energy’,
‘Units’,
‘Factory setting’
‘Choose language’,
‘Display’,
‘Machine settings
(4/5)’
T Select your language.
T Change the display settings.
T Activate the grinder selection.
‘Colour scheme’,
‘Café à la carte’,
‘Barista recipes’
26
4
Permanent settings in programming mode
Programme item
Sub-item
Explanation
‘Information (5/5)’
‘Product counter’,
‘Day counter’,
‘Maintenance
counter’,
T Keep track of all products prepared and view
the number of maintenance programmes
performed.
‘Version’
In the programme item ‘Product settings (2/5)’ you can make indi-
vidual settings for all speciality coffees, milk and hot water.
Product settings
Expert mode The following settings can be made in ‘Expert mode’:
Product
Ristretto,
espresso*,
coffee*
Coffee strength
; (extra-mild),
;; (mild),
Amount
More settings
Water: 25 ml – 290 ml Temperature (low, normal,
high), grinder on the left
and/or right (as %)
;;; (normal),
;;;; (strong),
;;;;; (extra-strong)
Two ristretti,
two espressi,
two coffees
Cappuccino*,
espresso
–
Water: 25 ml – 290 ml Temperature (low, normal,
(per cup)
high), grinder on the left
and/or right (as %)
Water: 25 ml – 290 ml Temperature (low, normal,
; (extra-mild),
;; (mild),
Milk: 0 sec. – 120 sec.
Milk foam:
high), grinder on the left
and/or right (as %)
macchiato*,
latte macchiato
;;; (normal),
;;;; (strong),
;;;;; (extra-strong)
0 sec. – 120 sec.
Interval:
0 sec. – 120 sec.
Two cappuccini,
two cafés au lait,
two espressi
macchiati,
–
Water: 25 ml – 290 ml Temperature (low, normal,
Milk: 0 sec. – 120 sec.
Milk foam:
high), grinder on the left
and/or right (as %)
0 sec. – 120 sec.
(per cup)
two latte
macchiati
Interval:
0 sec. – 120 sec.
27
4
Permanent settings in programming mode
Product
Coffee strength
; (extra-mild),
;; (mild),
Amount
More settings
Caffè latte*
Water: 25 ml – 290 ml Temperature (low, normal,
Milk: 0 sec. – 120 sec.
Milk foam:
high), grinder on the left
and/or right (as %)
;;; (normal),
;;;; (strong),
;;;;; (extra-strong)
0 sec. – 120 sec.
Portion of milk
foam,
–
Milk: 0 sec. – 120 sec.
Milk foam:
–
–
portion of milk*
Two portions of
milk foam,
two portions of
milk
0 sec. – 120 sec.
Milk: 0 sec. – 120 sec.
Milk foam:
–
0 sec. – 120 sec.
(per cup)
Pot,
Water: 25 ml – 290 ml Temperature (low, normal,
; (extra-mild),
;; (mild),
pot 2
(per stroke)
high), grinder on the left
and/or right (as %), number
of strokes (1–5; set number is
displayed during preparation)
;;; (normal),
;;;; (strong),
;;;;; (extra-strong)
Hot water*
–
Water: 25 ml – 450 ml Temperature (low, normal,
high)
(Products marked * are also available in ‘large’ size.)
E
In addition to the settings listed, you can reset the values for
all products to the factory settings.
Example: Proceed as follows in the ‘Expert mode’ to change the
amount of milk for a latte macchiato from ‘4 sec.’ to ‘6 sec.’, the
amount of milk foam from ‘12 sec.’ to ‘14 sec.’ and the amount of
water from ‘45 ml’ to ‘40 ml’.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Product
settings (2/5)’ is displayed.
T Press the ‘Expert mode’ button.
‘Expert mode’
28
4
Permanent settings in programming mode
E
E
Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
You can also select the products in the product selector. To do
this, turn the Rotary Switch to view the product selector.
T Press the ‘Latte macchiato’ button.
T Press the ‘Amount of milk’ button.
T Press the ‘+’ or ‘–’ button to change setting for the amount
of milk to ‘6 sec.’.
T Press the ‘Save’ button.
T Press the ‘Amount of milk foam’ button.
T Press the ‘+’ or ‘–’ button to change setting for the amount
of milk foam to ‘14 sec.’.
T Press the ‘Save’ button.
T Press the ‘Volume’ button.
T Press the ‘+’ or ‘–’ button to change setting for the fill vol-
ume to ‘40 ml’.
T Press the ‘Save’ button.
O
T Press the P button to exit programming mode.
‘Please select product:’
In the programme item ‘Product settings (2/5)’ / ‘Set consistency of
grind’ you can adjust both grinders separately to the degree of roast
of your coffee.
Setting the consistency
of grind
The consistency of grind is correct if the coffee flows regularly from
the dual spout. In addition a fine, thick crema forms.
Example: Proceed as follows to change the consistency of grind for
the grinder on the right.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Product
settings (2/5)’ is displayed.
T Press the ‘Set consistency of grind’ button.
‘Set consistency of grind’
T Press the ‘Right grinder’ button.
‘Right grinder’
29
4
Permanent settings in programming mode
T Press the ‘+’ or ‘–’ button to change the setting for the con-
sistency of grind.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Set consistency of grind’
O
T Press the P button to exit programming mode.
‘Please select product:’
In the programme item ‘Machine settings (3/5)’ / ‘Maintenance set-
tings’ you can make the following settings:
Maintenance settings
‘Filter’
U
Choose whether to operate your GIGA with or without an
U
external filter cartridge or change the filter capacity.
‘Water hardness’
U
If you do not have a filter cartridge, you will need to set the
U
water hardness (see Chapter 4 ‘Permanent settings in pro-
gramming mode – Setting the water hardness’).
‘Switch-on rinse’ / ‘Manual’
U
The switch-on rinse must be started manually.
U
‘Switch-on rinse’ / ‘Automatic’
U
The switch-on rinse is started automatically.
U
‘Rinse the milk system’ / ‘Manual after 10 min.’
U
You are prompted to rinse the milk system 10 minutes after
U
preparation of a speciality coffee with milk.
‘Rinse the milk system’ / ‘Manual immediate’
U
You are prompted to rinse the milk system immediately
U
after preparation of a speciality coffee with milk.
‘Rinse the milk system’ / ‘Automatic after 10 min.’
U
Milk system rinsing is automatically initiated 10 minutes
U
after preparation of a speciality coffee with milk.
‘Rinse the milk system’ / ‘Automatic immediate’
U
Milk system rinsing is automatically initiated approx. 30 sec-
U
onds after preparation of a speciality coffee with milk.
Example: Proceed as follows to make the machine prompt you to
rinse the milk system immediately after preparing a speciality cof-
fee with milk.
Precondition: ‘Please select product:’ is displayed.
30
4
Permanent settings in programming mode
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Maintenance settings’ button.
‘Maintenance settings’
T Press the ‘Rinse the milk system’ button.
‘Rinse the milk system’
T Press the ‘Manual immediate’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Maintenance settings’
O
T Press the P button to exit programming mode.
‘Please select product:’
The harder the water is, the more frequently the GIGA needs to be
descaled. It is therefore important to set the water hardness accu-
rately.
Setting the water
hardness
The water hardness can be adjusted on a continuous scale between
1° dH and 30° dH.
E
If you are using an external filter cartridge and have activated
it, it is not possible to set the water hardness.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Maintenance settings’ button.
‘Maintenance settings’
T Press the ‘Water hardness’ button.
‘Water hardness’
T Press the ‘+’ or ‘–’ button to adjust the water hardness.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Maintenance settings’
O
T Press the P button to exit programming mode.
‘Please select product:’
31
4
Permanent settings in programming mode
In the programme item ‘Machine settings (3/5)’ / ‘Save energy’ you
can permanently set an energy-saving mode (Energy Save Mode,
E.S.M.©):
Energy-saving mode
‘Save No’
U
All speciality coffees, speciality coffees with milk and hot
U
water can be prepared without having to wait.
‘Save Level 1’
U
After switching on, your GIGA is only ready for use for speci-
U
ality coffees and hot water. Before you can prepare a special-
ity coffee with milk, the machine must heat up.
Soon after the last preparation, the GIGA stops heating up.
U
After about 5 minutes the message ‘Energy Save’ is dis-
played.
‘Save Level 2’
U
After switching on, your GIGA is ready for use for all special-
U
ity coffees with and without milk, as well as hot water.
Soon after the last preparation, the GIGA stops heating up.
U
After about 5 minutes the message ‘Energy Save’ is dis-
played.
Example: Proceed as follows to change the energy-saving mode
from ‘Save Level 1’ to ‘Save Level 2’.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Save energy’ button.
‘Save energy’
T Press the ‘Save Level 2’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (3/5)’
O
T Press the P button to exit programming mode.
‘Please select product:’
32
4
Permanent settings in programming mode
You already set the time and date during first-time use. You can
change this setting.
Time and date
E
For the time format, you can choose between ‘24 hrs’ and
‘AM / PM’ (see Chapter 4 ‘Permanent settings in programming
mode – Units’).
Example: Proceed as follows to change the time.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Time / date’ button.
‘Time / date’
T Press the ‘Time’ button.
‘Time’
T Press the ‘+’ or ‘–’ button to set the hours.
T Press the ‘Save’ button.
T Press the ‘+’ or ‘–’ button to set the minutes.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Time / date’
O
T Press the P button to exit programming mode.
‘Please select product:’
In the programme item ‘Machine settings (3/5)’ / ‘Timer’ you can set
an individual switch-on and switch-off time for every day of the
week.
Timer
E
E
Automatic switch-on only works when the machine is switched
on at the power switch.
For the time format, you can choose between ‘24 hrs’ and
‘AM / PM’ (see Chapter 4 ‘Permanent settings in programming
mode – Units’).
Example: Proceed as follows to set your GIGA to switch on and off
at a time defined by you every day of the week.
Precondition: ‘Please select product:’ is displayed.
33
4
Permanent settings in programming mode
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Timer’ button.
‘Timer’
T Press the ‘Monday’ button (example).
‘Monday’
T Press the ‘+’ or ‘–’ button to set the hours (for ‘Switch
machine on’).
T Press the ‘P’ button.
T Press the ‘+’ or ‘–’ button to set the minutes (for ‘Switch
machine on’).
T Press the ‘P’ button.
T Press the ‘+’ or ‘–’ button to set the hours (for ‘Switch
machine off’).
T Press the ‘P’ button.
T Press the ‘+’ or ‘–’ button to set the minutes (for ‘Switch
machine off’).
T Press the ‘Every weekday’ button.
‘Saved’ appears briefly on the display. The switch-on and
switch-off times you just set are adopted for every day of the
week.
‘Timer’
O
T Press the P button to exit programming mode.
‘Please select product:’
By instructing your GIGA to automatically switch itself off, you can
cut down your energy consumption. If this function is activated,
your GIGA switches off automatically after the preset time following
the last action on the machine.
Automatic switch-off
You can set the automatic switch-off time to 15 minutes or 0.5–15
hours.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
34
4
Permanent settings in programming mode
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Timer’ button.
T Press the ‘Next’ button.
T Press the ‘Switch off after’ button.
‘Switch off after’
T Press the ‘+’ or ‘–’ button to change the setting.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Timer’
O
T Press the P button to exit programming mode.
‘Please select product:’
In the programme item ‘Machine settings (3/5)’ / ‘Units’ you can
make the following settings:
Units
Unit for amount of water: ‘ml’ or ‘oz’
U
Time format: ‘24 hrs.’ or ‘AM / PM’
U
Example: Proceed as follows to change the unit for the amount of
water from ‘ml’ to ‘oz’.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Units’ button.
‘Units’
T Press the ‘oz’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (3/5)’
O
T Press the P button to exit programming mode.
‘Please select product:’
35
4
Permanent settings in programming mode
In the programme item ‘Machine settings (3/5)’ / ‘Factory setting’
you can reset various settings to their factory settings:
Restore factory settings
‘All products’
U
The settings (amount of water, coffee strength, temperature
U
etc.) for all products are reset to the factory settings.
‘Machine’
U
All user settings are reset to factory settings. The GIGA then
U
switches off.
‘Empty system’
U
The system is emptied. Your GIGA then switches off.
U
Example: Proceed as follows to reset the values for all products to
the factory settings.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Factory setting’ button.
‘Factory setting’
T Press the ‘All products’ button.
‘All products’ / ‘Reset all products to the factory settings?’
T Press the ‘Yes’ button.
‘Saved’ appears briefly on the display.
‘Factory setting’
O
T Press the P button to exit programming mode.
‘Please select product:’
In this programme item you can set the language used by your
GIGA.
Language
Example: Proceed as follows to change the language from ‘English’
to ‘Deutsch’.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
36
4
Permanent settings in programming mode
g
E
T Turn the Rotary Switch until the programme item ‘Machine
settings (4/5)’ is displayed.
T Press the ‘Choose language’ button.
‘Choose language’
To display more languages, press the ‘Next’ button (bottom
right).
T Press the ‘Deutsch’ button.
‘Gespeichert’ appears briefly on the display.
‘Geräteeinstellungen (4/5)’
O
T Press the P button to exit programming mode.
‘Bitte wählen Sie Ihr Produkt:’
In the programme item ‘Machine settings (4/5)’ / ‘Display’ you can
make the following settings:
Display settings
‘Brightness’ (as percentages)
U
‘Contrast’ (high, normal, low)
U
‘Backlight’ (backlighting; as percentages)
U
Example: Proceed as follows to change the brightness of the display.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (4/5)’ is displayed.
T Press the ‘Display’ button.
‘Display’
T Press the ‘Brightness’ button.
T Press the ‘+’ or ‘–’ button to change the setting.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Display’
O
T Press the P button to exit programming mode.
‘Please select product:’
37
4
Permanent settings in programming mode
In this programme item you can set the background for the display
of your GIGA.
Background
E
The set background is only displayed on the start screen.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (4/5)’ is displayed.
T Press the ‘Colour scheme’ button.
‘Colour scheme’
T Press the ‘+’ or ‘–’ button to change the setting.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (4/5)’
O
T Press the P button to exit programming mode.
‘Please select product:’
In the programme item ‘Machine settings (4/5)’ you can activate or
deactivate the barista recipes. When the barista recipes are deacti-
vated they no longer appear in the product selector.
Barista recipes
Example: Proceed as follows to deactivate barista recipes.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (4/5)’ is displayed.
T Press the ‘Barista recipes’ button.
‘Barista recipes’
T Press the ‘Inactive’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (4/5)’
O
T Press the P button to exit programming mode.
‘Please select product:’
38
4
Permanent settings in programming mode
In the programme item ‘Information (5/5)’ you can view the follow-
ing information:
Querying information
‘Product counter’: Number of prepared coffee speciality cof-
U
fees, speciality coffees with milk and hot water
‘Day counter’: Number of prepared coffee speciality coffees,
U
speciality coffees with milk and hot water. This counter can be
reset to zero.
‘Maintenance counter’: Number of maintenance programmes
U
performed (cleaning, descaling etc.)
‘Version’: Software version
U
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Informa-
tion (5/5)’ is displayed.
T Press the ‘Product counter’ button.
‘Total cups’
E
You can also view the number of products prepared in the
product selector. To do this, turn the Rotary Switch.
T Press any button or the Rotary Switch to exit the programme
item.
‘Information (5/5)’
O
T Press the P button to exit programming mode.
‘Please select product:’
39
5
Maintenance
5
Maintenance
Your GIGA has the following integrated maintenance programmes:
Rinsing the coffee system (‘Rinse the coffee system’)
U
Rinsing the milk system in the dual spout (‘Rinse the milk
U
system’)
Cleaning the milk system in the dual spout (‘Clean the milk
U
system’)
Changing the filter (‘Change the filter’)
U
Cleaning the machine (‘Clean’)
U
Descaling the machine (‘Descale’) (only if filter is not acti-
U
vated)
E
E
Clean or descale the machine, rinse the milk system or change
the filter when you are prompted to do so.
Press the P button to view a list of the maintenance pro-
grammes (‘Maintenance status (1/5)’). When the bar is com-
pletely filled with red, your GIGA will prompt you to perform
the appropriate maintenance programme.
E
The GIGA will not prompt you to clean the milk system. In the
interests of hygiene, you should clean the milk system daily
when you have been preparing milk.
You can perform coffee system rinsing at any time.
Rinsing the coffee system
Precondition: ‘Please select product:’ is displayed.
T Place a receptacle under the dual spout.
O
T Press the P button.
‘Maintenance status (1/5)’
T Press the ‘Rinse the coffee system’ button.
‘Machine is rinsing.’, water flows out of the dual spout.
The rinse stops automatically. ‘Please select product:’
appears on the display.
40
5
Maintenance
Depending on the setting in programming mode, the GIGA prompts
you to rinse the milk system or automatically performs rinsing fol-
lowing milk preparation.
Rinsing the milk system
Example: Proceed as follows to rinse the milk system when
prompted to do so.
Precondition: ‘Rinse the milk system.’ and the c symbol are dis-
played.
T Place a receptacle under the dual spout.
O
T Press the P button.
‘Maintenance status (1/5)’
T Press the ‘Rinse the milk system’ button.
‘Milk system is being rinsed.’, water flows out of the dual
spout.
The rinse stops automatically. ‘Please select product:’
appears on the display.
To ensure that the milk system in the dual spout always works prop-
erly, you must clean it daily when you have been preparing milk. The
GIGA will not prompt you to clean the milk system.
Cleaning the milk system
CAUTION If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T
Use only original JURA maintenance products.
E
JURA Cappuccino Cleaner is available from specialised dealers.
Precondition: ‘Please select product:’ is displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
T Press the ‘Clean the milk system’ button.
T Press the ‘Start’ button.
T Press the ‘Start’ button again.
‘Cleaning agent for milk system.’
T Pour 250 ml of fresh water into a receptacle and add one
capful of Cappuccino Cleaner.
T Immerse the milk pipe in the receptacle.
41
5
Maintenance
T Place another receptacle under the dual spout.
T Press the ‘Next’ button.
‘Milk system is being cleaned.’, water flows out of the dual
spout.
‘Water for cleaning milk system.’
T Rinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the dual spout
again.
T Press the ‘Next’ button.
‘Milk system is being cleaned.’, the dual spout and the pipe
are rinsed with fresh water.
The operation stops automatically. ‘Milk system cleaning
complete.’ appears briefly on the display.
‘Please select product:’
The dual spout must be dismantled and rinsed daily if milk has been
prepared to make sure it functions perfectly and also in the interests
Dismantling and rinsing
the dual spout
of hygiene.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Press the releasing devices and pull the cover of the dual
spout up and off.
42
5
Maintenance
T Carefully pull the bottom part of the milk system down and
off.
T Remove the milk system from the dual spout.
T Remove the air intake pipe.
T Dismantle the milk system into its individual parts.
T Rinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in JURA Cappuccino Cleaner and then rinse them thor-
oughly.
T Reassemble the milk system. When doing this, note the
arrows (circled in red in the picture) on the individual parts.
43
5
Maintenance
T Fit the air intake pipe.
T Fit the assembled individual parts back in the dual spout and
press it firmly.
T Attach the bottom part of the milk system to the part
already inserted from below.
T Fit the cover of the dual spout. It will click into place audibly.
T Insert the milk pipe into the dual spout.
44
5
Maintenance
E
After the set amount of water has flowed through the external
filter cartridge, it will cease to work. Your GIGA will automati-
cally prompt you to change the filter.
Changing the filter
Example: Proceed as follows to change the filter when prompted to
do so.
Precondition: ‘Change the filter’ and the symbol c are displayed.
T Change the external filter cartridge as described in the
instructions for the cartridge.
O
T Press the P button.
‘Maintenance status (1/5)’
T Press the ‘Change the filter’ button.
‘Change the filter’ / ‘Do you really want to reset the filter
capacity?’
T Press the ‘Yes’ button
‘Change the filter’ / ‘Filter capacity has been reset.’
‘Please select product:’ appears on the display.
After 220 preparations or 80 switch-on rinses, the GIGA will prompt
you to clean it.
Cleaning the machine
CAUTION If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T
Use only original JURA maintenance products.
E
E
The cleaning programme lasts approximately 20 minutes.
Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E
JURA cleaning tablets are available from specialised dealers.
Example: Proceed as follows to clean when prompted to do so.
Precondition: ‘Clean machine.’ and the c symbol are displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
T Press the ‘Clean’ button.
T Press the ‘Start’ button.
T Press the ‘Start’ button again.
‘Empty coffee grounds container.’
45
5
Maintenance
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Press the Rotary Switch.’
T Place a receptacle under the dual spout.
T Press the Rotary Switch.
k
‘Machine is being cleaned.’, water flows out of the dual
spout.
The operation is interrupted, ‘Add cleaning tablet.’.
T Open the cover of the filler funnel for ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
‘Press the Rotary Switch.’
k
T Press the Rotary Switch.
‘Machine is being cleaned.’, water flows out of the dual spout
repeatedly.
The operation is interrupted, ‘Empty coffee grounds con-
tainer.’.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Clean’ / ‘Cleaning complete.’
Cleaning is now complete. Your GIGA is once more ready for
use.
The GIGA builds up deposits of limescale over time and automati-
cally prompts you to descale it when necessary. The degree of calci-
fication depends on the hardness of your water.
Descaling the machine
J
CAUTION If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T
T
Avoid contact with the skin or eyes.
Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
CAUTION If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
T
Use only original JURA maintenance products.
46
5
Maintenance
CAUTION If the descaling operation is interrupted, there may be damage to
the machine.
T
Allow the descaling programme to run to the end.
CAUTION If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T
Clean up any splashes immediately.
E
E
E
The descaling programme lasts approximately 50 minutes.
JURA descaling tablets are available from specialised dealers.
If you use a CLARIS filter cartridge and this is activated, you
will not be prompted to descale.
Example: Proceed as follows to perform descaling when prompted
to do so.
Precondition: ‘Decalcify machine.’ and the c symbol are displayed.
O
T Press the P button.
‘Maintenance status (1/5)’
T Press the ‘Descale’ button.
T Press the ‘Start’ button.
T Press the ‘Start’ button again.
‘Empty drip tray.’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Pour descaling agent into water tank.’
T Remove and empty the water tank.
T Completely dissolve 4 JURA descaling tablets in a receptacle
holding 800 ml of water. This may take several minutes.
T Pour the solution into the empty water tank and insert it into
the machine.
‘Press the Rotary Switch.’
47
5
Maintenance
T Place one receptacle under the dual spout and another
under the hot-water spout.
k
T Press the Rotary Switch.
‘Machine is being descaled.’, water flows repeatedly out of
the dual spout and the hot-water spout.
The operation stops automatically. ‘Empty drip tray.’ appears
on the display.
T Empty both receptacles.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank.’
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
‘Press the Rotary Switch.’
T Place the receptacles back under the dual spout and the hot-
water spout.
k
T Press the Rotary Switch.
‘Machine is being descaled.’, water flows out of the dual
spout and the hot-water spout.
The operation stops automatically. ‘Empty drip tray.’ appears
on the display.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Descale’ / ‘Descaling complete.’
Descaling is now complete. Your GIGA is once more ready
for use.
E
If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
48
5
Maintenance
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean containers. These traces may negatively affect
the coffee result. For this reason clean the bean containers from time
to time.
Cleaning the bean
container
Precondition: ‘Fill bean container.’ is displayed.
Q
T Switch the machine off with the On/Off button.
T Switch the machine off at the power switch.
T Open the service cover on the back of the machine by press-
ing above the JURA logo.
3
T Push the red sliding catch completely to the rear to close the
bean container.
T Turn the blue locking device outwards.
T Remove the bean container.
T Remove the aroma preservation cover.
T Empty the bean container.
T Clean the bean container with a soft, dry cloth.
T Fit the bean container.
T Turn the blue locking device inwards.
T Pull the red sliding catch completely forwards.
T Refit the service cover and fix it by pressing above the JURA
logo. It will click into place audibly.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
49
6
Display messages
6
Display messages
Message
Cause/Result
Action
‘Empty coffee
grounds
The coffee grounds container is full.
You cannot prepare any products.
T Empty the coffee grounds
container and the drip tray (see
Chapter 3 ‘Daily operation – Daily
maintenance’).
container.’
‘Coffee grounds
container not
fitted.’
The coffee grounds container is not
fitted. You cannot prepare any
products.
T Fit the coffee grounds container.
‘Drip tray not
fitted.’
The drip tray is not inserted correctly
or is not inserted at all. You cannot
prepare any products.
T Fit the drip tray.
‘Press the
The system must be filled with water
or the GIGA prompts you to continue
a started maintenance programme.
T Turn the Rotary Switch to
Rotary Switch.’
continue with the maintenance
programme or to fill the system.
‘Fill bean
One of the bean containers is empty.
You cannot prepare any speciality
coffees for which coffee beans are
required from this bean container.
You can prepare hot water or milk.
The GIGA is prompting you to rinse the
milk system.
T Fill the bean container (see
Chapter 1 ‘Preparing and using for
the first time – Filling the bean
container’).
container.’, the
bean container
status indicator
flashes.
‘Rinse the milk
system.’
T Press the P button and then the
‘Rinse the milk system’ button to
initiate milk system rinsing.
‘Clean machine.’
The GIGA is prompting you to clean it.
T Perform cleaning (see Chapter 5
‘Maintenance – Cleaning the
machine’).
‘Decalcify
machine.’
The GIGA is prompting you to
descale it.
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the
machine ’).
‘Change filter.’
After the set amount of water has
flowed through the external filter
cartridge, it will cease to work.
T Replace the external filter
cartridge (see Chapter 5 ‘Mainte-
nance – Changing the filter’).
The GIGA is prompting a filter change.
The dual spout or the cover of the dual
spout is not fitted correctly.
‘Spout is not
fitted.’
T Fit the cover of the dual spout or
the dual spout correctly.
50
6
Display messages
Message
Cause/Result
Action
‘Not enough
ground coffee.’
There is insufficient ground coffee in
the machine; the GIGA stops the
operation.
T The next time you prepare a
beverage, add more ground coffee
(see Chapter 2 ‘Preparation –
Ground coffee’).
‘Service cover is
not fitted.’
The service cover on the back of the
machine is not fitted. You cannot
prepare any products.
T Fit the service cover.
‘Please check the The ventilation slats on the top of
ventilation slats.’ the machine cannot be opened.
You cannot prepare any products.
T Contact customer support in
your country (see Chapter 11
‘JURA contact details / Legal
information’).
51
7
Troubleshooting
7
Troubleshooting
Problem
Cause/Result
Action
Insufficient foam is
produced when the milk
is frothed, or milk sprays
from the dual spout.
Coffee only comes out
The dual spout is dirty.
T Rinse and clean the dual spout (see
Chapter 5 ‘Maintenance – Cleaning
the milk system’).
Coffee or ground coffee has
T Put the grinder on a coarser setting
or use coarser ground coffee (see
Chapter 4 ‘Permanent settings in
programming mode – Setting the
consistency of grind’).
in drips when it is being been ground too finely and
prepared.
is blocking the system. The
same filter cartridge may
have been used several times
or the water hardness set
incorrectly in the program-
ming mode.
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the
machine ’).
‘Fill bean container.’ is
not displayed although
the bean container is
empty.
The bean monitor is dirty.
T Clean the bean container (see
Chapter 5 ‘Maintenance – Cleaning
the bean container’).
Preparation stops, ‘Fill
The sliding catch for the
T Open the service cover on the back
of the machine and pull the sliding
catch all the way out (see Chapter 5
‘Maintenance – Cleaning the bean
container’).
bean container.’ is briefly bean container has not been
displayed although the pulled out or has not been
bean container has been pulled out completely.
filled.
‘Empty drip tray.’
The metal contacts of the
drip tray are dirty or wet.
T Clean and dry the metal contacts on
is always displayed.
the back of the drip tray.
‘Error 2’ is displayed.
If the machine was exposed
to the cold for a long period
of time, heating is disabled
for safety reasons.
T Warm the machine at room
temperature.
Other ‘Error’ messages
are displayed.
–
T Switch the GIGA off at the power
switch. Contact customer support in
your country (see Chapter 11 ‘JURA
contact details / Legal information’).
E
If you were unable to solve the problem, contact customer
support in your country (see Chapter 11 ‘JURA contact details /
Legal information’).
52
8
Transport and environmentally friendly disposal
8
Transport and environmentally friendly disposal
In order to protect the GIGA from frost during transport, the system
must be emptied.
Transport / Emptying the
system
Precondition: ‘Please select product:’ is displayed.
T Place one receptacle under the dual spout and another
under the hot-water spout.
O
T Press the P button.
‘Maintenance status (1/5)’
g
T Turn the Rotary Switch until the programme item ‘Machine
settings (3/5)’ is displayed.
T Press the ‘Factory setting’ button.
‘Factory setting’
T Press the ‘Empty system’ button.
‘Press the Rotary Switch.’
k
T Press the Rotary Switch.
‘System is emptying.’, water flows out of the dual spout and
the hot-water spout.
The operation stops automatically. Your GIGA is switched
off.
Please dispose of old machines in an environmentally neutral way.
H
Disposal
Old machines contain valuable, recyclable materials which should
be recycled. Please therefore dispose of old machines via suitable
collection systems.
53
9
Technical data
9
Technical data
Voltage
220–240 V ~, 50 Hz
2300 W
Power
Airborne noise emitted
Ambient conditions
L
P
< 70 dB (A)
Humidity max. 80%
Ambient temperature 10–35 °C
Conformity mark
A S
Energy consumption
approx. 30 Wh
‘Save energy’ / ‘Save No’
Energy consumption
approx. 12 Wh
approx. 15 Wh
‘Save energy’ / ‘Save Level 1’
Energy consumption
‘Save energy’ / ‘Save Level 2’
Pump pressure
Static, max. 15 bar
max. 0.6 MPa
2.6 l
Inlet pressure
Holding capacity of water tank
Holding capacity of bean container
Holding capacity of coffee grounds container
Cable length
2× 650 g
max. 40 portions
approx. 1.2 m
approx. 18.9 kg
32 × 57 × 48 cm
Weight
Dimensions (W × H × D)
Technical data for permanent water connection:
Permanent water connection G 3/4" external thread
Water supply line
Metal hose with G 3/4" union nut (hose must comply with the
applicable regulations for your country)
with non-return valve (type EA) and filter
Shut-off valve
Information for testers (repeat test in accordance with DIN VDE
0701-0702): The central grounding point (CGP) is located on the
front of the machine below the JURA logo (turn JURA logo anti-clock-
wise).
54
10 Index
10 Index
Cover
Service cover 5
A
Addresses 60
Storage compartment 4
Water tank 4
Aroma preservation cover
Bean container with aroma preservation
cover 4
Automatic switch-off 33, 34
Automatic switch-on 33
Cup grille 4
Customer support 60
D
Date 33
Descaling
Machine 46
Display 5
Display messages 50
Display settings 37, 38
Disposal 53
Double product 17
Drip tray 4
Dual spout
B
Background 38
Barista recipes 19
Preparation 20
Programming mode 38
Bean container
Bean container with aroma preservation
cover 4
Cleaning 49
Filling 10
Dismantling and cleaning 42
Height- and width-adjustable
dual spout 4
Status indicator 4
Bean container status indicator 4
Beans à la carte
Activating the grinder selection 21
E
F
Bus bar
Emptying the system 53
Energy-saving mode 32
Errors
Troubleshooting 52
Espresso 16
Technical data 54
Button
On/Off button 5
P button (programming) 5
Expert mode 27
C
Cappuccino 16
Factory settings
Restore factory settings 36
Filler funnel
Filler funnel for ground coffee 4
Filling
Cappuccino frother cleaning
Cleaning the milk system 41
Cappuccino frother rinsing
Rinsing the milk system 41
CLARIS filter cartridge
Changing 45
Bean container 10
Filter
Cleaning
Changing 45
First-time use 11
Bean container 49
Machine 45
Coffee 16
G
Coffee à la carte 16
Coffee grounds container 4
Consistency of grind
Setting the consistency of grind 29
Contact details 60
Grinder
Activating the grinder selection 21
Setting the consistency of grind 29
Ground coffee 18
Measuring spoon for ground coffee 4
55
10 Index
Preparation 16
H
At the touch of a button 17
Barista recipes 20
Cappuccino 16
Hotline 60
Hot water 23
Hot-water spout
Height-adjustable hot-water spout 4
Coffee 16
Espresso 16
Ground coffee 18
Hot water 23
Latte macchiato 16
Ristretto 16
I
Instant coffee
Ground coffee 18
Internet 10
J
Two speciality coffees 17
Using the product selector 18
Preparation options 16
At the touch of a button 17
Using the product selector 18
Problems
Troubleshooting 52
Product selector 16, 18
Product settings 27
Expert mode 27
JURA
Contact details 60
Internet 10
L
M
Language 36
Latte macchiato 16
Locking device 5
Machine
Programming mode 26
Automatic switch-off 34
Background 38
Cleaning 45
Descaling 46
Rinsing the coffee system 40
Setting up 10
Barista recipes 38
Display settings 37
Energy-saving mode 32
Language 36
Maintenance settings 30
Product settings 27
Querying information 39
Restore factory settings 36
Setting the consistency of grind 29
Setting the water hardness 31
Time and date 33
Switching off 25
Switching on 24
Mains cable 4
Maintenance 40
Daily maintenance 24
Maintenance settings 30
Measuring spoon for ground coffee 4
Messages, display 50
Milk
Connecting milk 15
Milk system
Timer 33
Units 35
Cleaning 41
Rinsing 41
Proper use 6
Q
P
Querying information 39
Quick installation 12
Quick mode 27
Permanently setting amounts for the
cup size 20
Permanent settings in programming
mode 26
Power switch 4
56
10 Index
R
S
U
V
Recipes
Barista recipes 19
Rinsing the coffee system 40
Ristretto 16
Rotary Selection 16
Product selector 18
Rotary Switch 5
Units 35
Use, First-time 11
Ventilation slats 4
Venti Ports
Ventilation slats 4
W
Water hardness
Safety 6
Safety information 6
Service cover 5
Service socket 5
Settings
Determining the water hardness 15
Setting the water hardness 31
Water tank 4
Website 10
Maintenance settings 30
Permanent settings in programming
mode 26
Setting up
Setting up the machine 10
Sliding catch 5
Splash guard 4
Spout
Height-adjustable hot-water spout 4
Height- and width-adjustable
dual spout 4
Switching off
Machine 25
Switching on
Machine 24
Switch-off
Automatic switch-off 33, 34
Switch-off time 33
Switch-on
Automatic switch-on 33
Switch-on time 33
Symbol description 3
T
Technical data 54
Tel 60
Time 33
Time format
Programming mode 35
Timer 33
Transport 53
Troubleshooting 52
Two products 17
57
58
59
Art. 71124/GIGA X7c/en/201210
11 JURA contact details / Legal information
11 JURA contact details / Legal information
Your JURA service partner
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel. +41 (0)62 38 98 233
Directives The machine complies with the following directives:
2006/42/EC – Machinery Directive
U
U
U
2004/108/EC – Electromagnetic Compatibility
2009/125/EC – Ecodesign Directive
Technical changes We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colours of the machine. Some details of
your GIGA may vary.
Feedback Your opinion is important to us! Use the contact link at
Copyright The instructions for use contain information which is protected by
copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.
60
|
Ingersoll Rand Air Compressor EP50 PE User Manual
Ingersoll Rand Marine Sanitation System 612805 User Manual
Inova Staple Gun BT125 User Manual
Invacare Mobility Aid Excel User Manual
JBL Portable Speaker LS360C User Manual
JVC Home Security System TM21A2U User Manual
JVC VCR HR J255EE User Manual
Kenmore Blender 7904422 User Manual
Kenwood Portable DVD Player KVT 817DVD User Manual
Kramer Electronics Car Stereo System KDS MP1 User Manual